+高级检索
基于CEL方法的Al/Mg搅拌摩擦焊温度场及材料混合流动研究
作者:
作者单位:

1.南昌航空大学;2.西北工业大学

作者简介:

通讯作者:

中图分类号:

TG453

基金项目:

轻合金加工科学与技术国防重点学科实验室基金(项目号EG202103420), 国家自然科学基金(项目号52105357),先进焊接与连接国家重点实验室基金(项目号AWJ-23M12)


Temperature field and material mixing flow in friction stir welding of dissimilar Al/Mg alloys based on CEL approach
Author:
Affiliation:

1.Nanchang Hangkong University;2.Northwestern Polytechnical University,Xi’an

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    本文基于耦合欧拉-拉格朗日(CEL)方法建立5A06铝合金与AZ31B镁合金对接搅拌摩擦焊(FSW)的全热力耦合数值模型,并结合试验测试对Al/Mg异种金属FSW过程的温度场及材料混合流动特征进行研究。数值模拟所得特征点的温度循环曲线、焊缝表面形貌以及横截面上异种材料的混合分布状态均与试验结果吻合良好。在此基础上,采用质点追踪法对材料混合流动行为进行了深入分析。结果显示,高温区集中分布在轴肩下方区域,返回侧(Mg侧)温度较低温度梯度较大。焊缝区上表面材料熔合线偏向于前进侧(Al侧)。搅拌针附近材料流动剧烈,前进侧和返回侧的大部分材料都较均匀地沉积于搅拌针后方。前进侧与返回侧材料在水平和竖直方向上的交叉混合流动,最终形成了两种材料“咬合式”的界面特征。

    Abstract:

    A fully coupled thermo-mechanical numerical model is developed for the butt friction stir welding (FSW) of 5A06 aluminum alloy and AZ31B magnesium alloy based on the coupled Eulerian-Lagrangian (CEL) method, and the temperature field and material mixing flow characteristics during FSW process are studied by numerical simulation and experimental tests. The temperature cycle curves, the weld surface morphology and the mixed distribution of dissimilar materials on the cross section obtained by numerical simulation are in good agreement with the experimental results. On this basis, the particle tracking method is used to analyze the mixing flow behavior of dissimilar materials. The results show that the high temperature zone is located in the region below the tool shoulder, and the temperature on the retreating side (Mg side) is lower and its gradient is larger. The fusion line of dissimilar materials on the top surface is inclined to the advancing side (Al side). The material near the pin flows significantly and most of the materials deposit evenly on the advancing and retreating sides behind the pin. The mixing flow of the materials on the advancing and retreating sides in the horizontal and vertical directions finally forms the zig-zag interface characteristics of the two materials.

    参考文献
    相似文献
    引证文献
引用本文

段亚雄,刘其鹏,高月华,李雯,柯黎明,牛鹏亮,徐洋.基于CEL方法的Al/Mg搅拌摩擦焊温度场及材料混合流动研究[J].稀有金属材料与工程,2023,52(7):2565~2572.[Duan Yaxiong, Liu Qipeng, Gao Yuehua, Li Wen, Ke Liming, Niu Pengliang, Xu yang. Temperature field and material mixing flow in friction stir welding of dissimilar Al/Mg alloys based on CEL approach[J]. Rare Metal Materials and Engineering,2023,52(7):2565~2572.]
DOI:10.12442/j. issn.1002-185X.20220560

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:2022-07-02
  • 最后修改日期:2023-07-24
  • 录用日期:2022-08-12
  • 在线发布日期: 2023-08-09
  • 出版日期: 2023-07-27